- Full Description
- Specifications
- What's Included
- Demo Videos
- Reviews
With highly refined software, new wireless radios, and a redesigned chassis, these new models are the most reliable and capable monitoring solutions we have ever built. Metadata and timecode support, 3D LUTs, dual inputs/outputs, multicast capable, manual frequency selection and USB 3.0 GRAB Engine are all included on these new models but with the following new features:
![]() |
Longer Range Transmit visually lossless |
![]() |
20MHz Channels Use more than twice as many Bolts in one location or avoid interference like never before. |
![]() |
2 New DFS Channels Operate interference-free |
![]() |
20% Smaller Chassis Not just smaller, but lighter too, allowing these models to integrate into any rig unnoticed. |
![]() |
Individual Identity Easily identify which Bolt |
![]() |
Rapid Reconnection Reconnect times during a dropped link are now instantaneous once you move back into range. |
![]() |
Built-In HDMI to SDI Converter Perfect for use with MoVI and other gimbals, Bolt’s TX has a built-in HDMI to SDI converter, allowing you to connect both your on-camera monitor and video source via the same device. |
![]() |
More Robust Than Ever Before Reach your Bolt’s full range |
More about the Bolt 1000
- Latency: < 0.001 seconds
- Range: 1000ft
- Multicast: Up to 4 Rx
- Size (TX): 24x66x102mm
- Weight TX / RX: 238g / 380g
- Input / Output: 3G-SDI & HDMI
- Resolution / Frame Rate: 1080p60
- TX HDMI / SDI Converter: YES
- Number of 20 MHz DFS Channels: 0
- Number of 40 MHz DFS Channels*: 11
- Rapid connect: YES
- Gen 1 Sidekick Compatible: NO
- Metadata support: YES
- USB 3.0 Grab Engine: YES
* Based on USA channels. Channel availability may vary by region.
Technical Specifications
Bolt 1000 Transmitter
Video Input
- 1 x 75 Ohm BNC
- 1 x Type A receptacle HDMI
Video Output
- 1 x 75 Ohm BNC(Loop-out)
Video Delay (Tx to Rx)
- <0.001sec (when no video format conversion is enabled)
Color Sampling
- Y:Cb:Cr = 4:2:2, 8-bit for SDI (10-bit with no format conversion and FPGA v.1.1.0 or later); RGB 4:4:4 (HDMI out, 8-bit color)
Supported Resolutions
- 1080p60/59.94/50/30/29.97/25/24/23.98
- 1080psf30/29.97/25/24/23.98
- 1080i60/59.94/50
- 720p60/59.94/50
- 480p59.94/576p50 (via HDMI ports only)
- 480i(NTSC)/576i(PAL)
Wireless
- Up to 1000ft line of sight
- Non-DFS Frequencies:
- US: 5.19 ~ 5.23 GHz and 5.755 ~ 5.795 GHz
- EU & JP: 5.19 ~ 5.23 GHz
- DFS Frequencies:
- US: 5.27 ~ 5.55 GHz and 5.67 GHz
- EU & JP: 5.27 ~ 5.67 GHz
RF Power
- 19dbm EIRP(with two 5dbi TX antennas)
Noise Rejection
- Can coexist with WiFi and 5GHz cordless phones
Audio
- Format Support: 48kHz 24-bit PCM
Physical
- Dimensions: 0.95"x2.6"x4.47"(24mmx66mmx101.5mm)
- Weight: 8oz(226g)
- Operating temperature:
- Milled Aluminum
Mountability
- Multiple mounting options with 4-40 holes
- Multiple mounting options with 1/4" hole
Power
- 2-Pin Lemo 7-28 VDC
- No Internal Battery
- Consumption: 7.5 Watts
Bolt 1000 Receiver
Video Output
- 1 x USB 3.0 micro B receptacle
- 1 x 75 Ohm BNC
- 1 x Type A receptacle HDMI"
Video Delay (Tx to Rx)
- <0.001sec (when no video format conversion is enabled)
Color Sampling
- Y:Cb:Cr = 4:2:2, 8-bit for SDI (10-bit with no format conversion and FPGA v.1.1.0 or later); RGB 4:4:4 (HDMI out, 8-bit color)
Supported Resolutions
- 1080p60/59.94/50/30/29.97/25/24/23.98
- 1080psf30/29.97/25/24/23.98
- 1080i60/59.94/50
- 720p60/59.94/50
- 480p59.94/576p50 (via HDMI ports only)
- 480i(NTSC)/576i(PAL)
Wireless
- Up to 1000ft line of sight
- Non-DFS Frequencies:
- US: 5.19 ~ 5.23 GHz and 5.755 ~ 5.795 GHz
- EU & JP: 5.19 ~ 5.23 GHz
- DFS Frequencies:
- US: 5.27 ~ 5.55 GHz and 5.67 GHz
- EU & JP: 5.27 ~ 5.67 GHz
RF Power
- 17dbm EIRP(with one 2dbi TX antenna)
Noise Rejection
- Can coexist with WiFi and 5GHz cordless phones
Audio
- Format Support: 48kHz 24-bit PCM /li>
Physical
- Dimensions: 5.5” x 3.5” x 1.0”(139mm x 88.5mm x 25 mm)
- Weight: 13.3oz(376g)
Mountability
- Multiple mounting options with 4-40 holes
- Multiple mounting options with 1/4" hole
Interfaces
- OLED display with joystick navigation buttons
Power
- 2-Pin Lemo 7-28 VDC
- No Internal Battery
- Consumption: 8.5 Watts
What's in the Box
- 1x Teradek Protective Case waterproof with custom foam (12 in x 9 in x 4.5 in - 30.48cmx 22.86cm x 11.43 cm)
- 5x Wireless Antennas (2dBi 2.4/5.8GHz) - For Rx
- 2x Wireless Antennas (2dBi 2.4/5.8GHz) - For Tx
- 1x 2-pin Lemo to PowerTap 18 inch Cable
- 1x Hot Shoe Adapter (1/4"-20 inch)
- 1x Lightstand Adapter (1/4"-20 inch)
- 2x SDI (BNC to BNC) Cable 10 inch
- 1x HDMI 18in Cable (Type A to Type A)
- 1x USB 3.0 Cable A to Micro B (3.ft Length)
- 1x PSU 2-Pin Lemo to 18W AC Adapter 6ft cable
- 1-Year Warranty
Related Products